the colors i mean. In the games it have more colors

Well, those are the colors its had since its debut, don't know what to tell ya.

really? then the games really improved it.

Aren't the shades (the blue especially) a bit darker in the movie?

new images of the MG GN-X from ngeekhiong

http://farm3.static.flickr.com/2751/...96f1cf79e0.jpg

http://farm3.static.flickr.com/2722/...0c3828381c.jpg

http://farm5.static.flickr.com/4052/...c6d44604bc.jpg

http://farm5.static.flickr.com/4028/...c98b29c0e2.jpg

http://farm5.static.flickr.com/4020/...8a6595edd7.jpg

you'll be getting only 1 GN-Drive base... and markings for Sergei (11), Soma (20), Patrick (1) & Daryl (21) will be given event though you'll only get figures of Sergei and Soma. :( :(

can't really see the pictures properly, but it looks like the GN-Claw can function as it should be.

There's an error. It should be UN GN tau-drive MS, not ESF.

GN-X Failure mode - Includes Patrick And no upper body.

HG 1/144 00 Gundam 7S/G - Feb 2010 Release
http://thumbnail.image.rakuten.co.jp...3112619358.jpg

Do you guys believe that the huge GN Buster Sword II is mounted onto the GN Drive by just 1 connector? (The same way you mount the GN Shield.) 1 connector for a huge sword?

Same connector principle for the Damashi version I believe. It seems to be stable though.

No connections onto the cones whatsoever? Just hangs over the cone?

The connection point seems to be stable enough with the Raiser wings and GN shield. It's not like there are any more connection points to utilize on the cones.

Given the size and weight of the buster sword, worrying about whether the drive holder will sag under the weight of it after some time is the real question.

I'm more concerned over whether there's going to be any sort of connections on the cones itself. Something like the Raiser's wings connected into 1 of the trench of the cone.

My drive cones are modified up with verniers (as where they should be in the trenches). Any connections like the Raiser wings for the 7SG will not be nice for me, or I'll have to mod up a 3rd cone for this.

I've got a huge problem for my HG 00 Gundam/Raiser.

The hole at the bottom thats suppose to connect to the stand?Its become sort of loose,so now its grip over 00 isnt as strong anymore.

In 00 Raiser form,it used to cause this problem slightly before because of its weight,but for some reason now it wont even hold 00 Gundam in place except conservative non slope poses of course.

I know its 00's hole and not the stand because I've tested it several stands,some of which are in good condition and handle my others nicely too.

So,anybody got any tips on how to fix this?And has anybody here encountered this problem before?

i've got a trick to fix that, what i usually do is i take a small piece of toilet paper and put between the stand + hole, it usually tightens it enough, easy to remove aswell, no need for superglue or anything like that, multiple layers works aswell, though be careful when putting the stand into the hole, you dont want to break anything.

To bad the HG 1/144 00 Gundam 7S/G doesn't come with the gn blade III, that would have made this puppy complete.
then again, that doesn't fit bandai's marketing plans does it...

Well, there is the fact that the 00 7S/G never actually uses the GN Sword III as far as I know. The original 00 7S never uses it as its not yet built, and I don't think the 7S/G uses it either.

it wasn't for a sence of belong, more of a sence in complete.

one kit will all 00 weapons (wether the normal or 007s gn long/short blade) :P

No, you see, that's what happens after they release the 00 Gundam Seven Sword/G.

Come out of your little fantasy world man. Bandai never includes all the weapons a Gundam uses at once.

it's my fantasy world that keeps me sane-ish...! :P