AnimeSuki.com Forum

AnimeSuki Forum (http://forums.animesuki.com/index.php)
-   Gundam (http://forums.animesuki.com/forumdisplay.php?f=40)
-   -   Gundam Models Discussion Thread (http://forums.animesuki.com/showthread.php?t=23320)

ZeddNL 2010-08-11 09:49

Haha MG Ex-S.
The mother of all bricks!

I want a MG Kshatriya (or when I land a better job and it wont come ill get the resin I geuss)

Winchester 2010-08-11 11:46

Don't care if it lacks posability and whatnot, it's big, has loads of detail, and a truckload of parts. It will take at least a week to build, and building it is the fun part!

Is there *any* hope whatsoever of a HGUC V2 Gundam in the relatively near future? Sure, I could get the 1/144 no grade, but that's a fifteen+ year old kit that won't look very good next to the HGUCs I want to display it with...


SP

SonicSP 2010-08-11 17:23

Quote:

Originally Posted by bio9205 (Post 3185902)
I think we established that a long time ago...



Yes they are. Just not sure if all of them can be hand held.

I'm really hoping for trans clear coloured parts for Harute: Specifically his green GN blade and purple visor. It would really suck if those were just trans clear...

Bandai usually release the Condenser Blades in green, so I think THAT is safe at least. The visor I think is more unlikely.

Quote:

Originally Posted by Kitaeryu (Post 3185929)
I'm REALLy hoping that the 00Q variant is released in 1/100 scale and is not limited, and not like the awesome XN raiser which was only released as a limited 1/144.

I think its a pity that Bandai doesn't make more models of the 00 side stories, I find their designs to be particularly awesome, even as good as the main series designs.

That doesnt mean they wont. Bandai was just in the middle of milking some of those who compatible runners. I'm hoping they'd do more too.

Quote:

Originally Posted by StrikeFreedomV2 (Post 3185794)
According to gundam.tk's review, they are wieldable.

Quote:

Originally Posted by LoweGear (Post 3186046)
Only two of the Sword Bits can be properly wielded by hand. However it seems to be more of an accident in design, since the "handles" on the Sword Bits used to hold them on the HG 00 Qan[T] are also the primary connection points for the larger Bits in Buster Sword and Buster Rifle form. And of course, said connectors are conspiciously absent from the actual drawing of the Bits themselves, leading me to believe they're a model-kit only concession. :heh:

Its cool then, two is good enough even if its an accident. I just want mine to be able to do it.

Quote:

Originally Posted by ZeddNL (Post 3186089)
Left is 00Raiser's manual, Right 00Q:
http://i35.tinypic.com/dgqi3m.png

So with cutting off some pegs you can glue them, if you are a good modeler I would rather mod 00Q's backpack to have the mounts but still, It should be pretty easy.

I think I'd cut the pegs and use the modeling cement on them. And if cement wont work I can just paint the surface and stick it before it dires right. I swear paint is the strongest permanant glue I've seen........

-----------------



By the way, if its not mentioned yet, there's an add on set for the HG 00Q in the February issue of the Hobby Japan. The official release date for the mag is on Christmas aka 12/25. News and pic credit goes to Homeless plus wherever she gets it from.

Spoiler for 00Q Add On:




Spoiler for HGUC The-O (Gunpla Builders version):


Spoiler for HGUC Gelgoog (Gunpla Builders version):

MakubeX2 2010-08-11 18:36

http://img294.imageshack.us/img294/6...1535151492.jpg

00Q for nearly half it's price slashed. Only at premier of the movie. Is Bandai trolling at the mainstream consumers or what ?

duotiga 2010-08-12 08:26

give me the metallic ver & i will buy =x

ZeddNL 2010-08-12 09:30

Quote:

Originally Posted by MakubeX2 (Post 3186964)
00Q for nearly half it's price slashed. Only at premier of the movie. Is Bandai trolling at the mainstream consumers or what ?

More like trolling western fans, we already pay shitloads of money to import/ship them over.

anyway I think the rumored 2010 PG will be 00Qan[T] due to PG 00raiser having chest space for a GN drive and all.

Kitaeryu 2010-08-12 21:48

Has anyone tried Krylon Acrylic Crystal Clear Satin as a topcoat before? If anyone has used it, what is the quality like? And what is the difference between Satin and Flat? I'm looking for a matte finish so which one would be best? And also, if I am going to spray this over just panel lines and decals (no paint) to make plastic seem/feel less plastic-y is this the right choice?

I would prefer to use this than Mr. Topcaot since the Krylon is in a local store near me. =D
Here is the website for it: http://www.krylon.com/products/acrylic_crystal_clear/ (i'm referring to the flat/satin colors even though the website image says gloss =D )
Thanks in advance.

Sworra 2010-08-13 00:30

Quote:

Originally Posted by Kitaeryu (Post 3189019)
Has anyone tried Krylon Acrylic Crystal Clear Satin as a topcoat before? If anyone has used it, what is the quality like? And what is the difference between Satin and Flat? I'm looking for a matte finish so which one would be best? And also, if I am going to spray this over just panel lines and decals (no paint) to make plastic seem/feel less plastic-y is this the right choice?

I would prefer to use this than Mr. Topcaot since the Krylon is in a local store near me. =D
Here is the website for it: http://www.krylon.com/products/acrylic_crystal_clear/
Thanks in advance.

That Krylon is a gloss coat so you wont get a matt finish. If there is another Can of that stuff that says Clear and Flat then id say try it out. I for one have no used the product but i thought id give you a heads up from the webpage you linked us. Good luck.

Haha i looked back at that webpage link and they do have the Flat clear coat. Don't bother with Gloss or Satin, I think satin is a semi gloss.. but i could be wrong.

gummybear 2010-08-13 00:40

Quote:

Originally Posted by MakubeX2 (Post 3186964)
http://img294.imageshack.us/img294/6...1535151492.jpg

00Q for nearly half it's price slashed. Only at premier of the movie. Is Bandai trolling at the mainstream consumers or what ?

not really, I never like the clear see through models. I only care about the special addons versions.

JC... 2010-08-13 04:01

I don't see the point in clear HGs, there's not really any frame to see...

loon1688 2010-08-13 09:55

HG 1/144 GNT-0000 00 QAN[T]
Now wait for 3 others partners mobile suits.....
Zabanya,Harute, Raphael.......
Don't know later will got any adding weapons or not?
http://i900.photobucket.com/albums/a...8/DSC01137.jpg
http://i900.photobucket.com/albums/a...8/DSC01139.jpg
http://i900.photobucket.com/albums/a...8/DSC01141.jpg
http://i900.photobucket.com/albums/a...8/DSC01145.jpg
http://i900.photobucket.com/albums/a...8/DSC01148.jpg
http://i900.photobucket.com/albums/a...8/DSC01149.jpg

GameraBaenre 2010-08-13 13:15

Project that I've been currently working on, a Gouf Custom resin conversion kit for the Gouf 2.0 frame. Here's the progress details: http://gamerabaenre.com/gouf_conv_prog.htm

The kit is still in progress so here's a teaser picture:


Baring anything catastrophic happening, I should have this sucker completely by the end of this weekend...

JC... 2010-08-13 14:27

Beautiful Gouf. It looks really menacing.

GN0010 Nosferatu 2010-08-14 01:50

Both Braves get a November release! WOOT!

http://ngeekhiong.blogspot.com/2010/...dam-super.html

JC... 2010-08-14 15:03

Does anyone have Angelo Sauper's Geara Zulu yet?

SonicSP 2010-08-14 15:52

Quote:

Originally Posted by loon1688 (Post 3189869)

Wahhhhh I'm so jealous......my store does not have it yet -_-

Yea, there confirmation of an addon. Its coming with the Hobby Japan February Issue as a limited release.

The release date officially is 25/12 2010, aka Christmas.

GameraBaenre 2010-08-14 16:06

Just finished this guy: http://gamerabaenre.com/?p=1073

Completed page: http://gamerabaenre.com/gouf_conv.htm
Progress page: http://gamerabaenre.com/gouf_conv_prog.htm


SonicSP 2010-08-14 16:48

Another fine one I must say.

velocity7 2010-08-14 22:43

Someone should try modding the 00 Quanta shield so that it can hold 00 Gundam equipment, such as 0 Raiser wing binders, 00 Seven Sword/G equipment, etc.

bio9205 2010-08-15 05:46

Anyone have a suggestion for a conventional/easily available glue-ish thing that I can use for tightening ball joints? I'm not very experienced with super glue and cement, so I'm not that keen on using those.


All times are GMT -5. The time now is 12:48.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.